Samsung A56 5G ISP Pinout Diagram

The Samsung A56 5G ISP Pinout Diagram is a critical component for professionals working with the device's hardware, providing detailed information about the different connections on the board.

This diagram maps out the Interface Serial Protocol (ISP) pins used for debugging, flashing firmware, and conducting low-level repairs. Each pin has specific functions such as data transfer, power management, and communication protocols between the processor and external devices. Typically, ISP pinouts include TX, RX, GND, and VCC connections, alongside other important signals for operations like boot mode and reset.

Post Index:Understanding these pinouts is essential for technicians who need to diagnose hardware issues, upgrade firmware, or recover data from damaged devices. It's worth noting that the ISP pinout for the Samsung A56 5G is unique compared to other models in the same series, designed to handle the high-speed 5G capabilities of the device while ensuring efficient power usage and minimal signal interference.

Samsung A56 5G ISP Pinout Solution

Having trouble flashing your Samsung Galaxy A56 5G (SM‑A566B/E) or removing the FRP lock? The UFS ISP pinout—similar to the one used for the Samsung Galaxy M33 (SM‑M336B)—can help. If your tools fail to flash stock firmware, remove locks, or bypass Factory Reset Protection, using the A56 UFS ISP connection lets you reset the user lock,

write a UFS dump, or erase the MDM lock. Follow the complete tutorial and photos below to quickly locate the UFS ISP test points on the Galaxy A56; with a compatible ISP tool such as EasyJTAG Plus (or any other ISP‑capable box), you can connect directly to the device’s storage and perform FRP bypasses or user data resets. Check out the guide below.

What is the Samsung A56 5G ISP Pinout?

UFS ISP (Universal Flash Storage In‑System Programming) pinout is the arrangement of test points on a device’s circuit board that provides direct access to its UFS flash memory. By wiring into these pins, technicians and advanced users can bypass normal software interfaces and work directly with the phone’s storage to flash firmware, recover a dead boot, or remove security locks.

For Samsung models like the Samsung A56 5G ISP Pinout (and similarly the Galaxy M33, SM‑M336B), UFS ISP access is often required when a wrong firmware flash leaves the phone unbootable or when conventional unlocking methods fail. Specialized boxes that support UFS — for example EasyJTAG Plus — are typically used for these repairs; with the right equipment and skills you can perform boot repairs and, in some cases, remove pattern/password, FRP, or MDM locks that can’t be cleared through standard software tools.

Samsung Galaxy A56 (SM-A566B/E) UFS ISP Pinout Image

Samsung A56 5G ISP Pinout Start by removing the back cover of your Samsung Galaxy A56. Next, carefully disconnect the battery, fingerprint reader, and camera from the motherboard. Unscrew and remove the screws holding the motherboard in place, then gently lift it out and set it aside safely.

Also read: Samsung A36 SM-A366E EMMC Ways ISP PinOut

Once the motherboard is removed, locate the eMMC pins for TxOp, TxOn, RxOp, and RxOn on the device. You may need to cut through the steel cover to access these pins.

Next, take the UFI box and extract the adapter from it. The pins on the adapter should match those identified earlier (TxOp, TxOn, RxOp, RxOn). Use jumpers to connect these four pins between the base and the adapter, ensuring the USB connection is left intact to power VCC and VCCQ.

Insert the connector into the UFI box, then connect the box to your computer. Finally, reconnect the battery and use a USB cable to connect your phone to the computer for further operations.

Removing FRP Lock on a Samsung Galaxy A56 5G Using EasyJTAG Plus

This guide outlines the procedure for bypassing the Factory Reset Protection (FRP) lock on a Samsung Galaxy A56 5G using the EasyJTAG Plus box.

Required Equipment:

Samsung Galaxy A56 5G (with a sufficiently charged battery)

EasyJTAG Plus box with the appropriate UFS adapter

Micro USB cable

A computer or laptop with the EasyJTAG software installed

Step-by-Step Instructions:

Prepare the Device: Power off the Samsung Galaxy A56 5G. Carefully remove the device's back panel to access the internal circuitry and locate the UFS ISP pinout.

Samsung A56 5G ISP Pinout Connect Hardware: Connect the wires from the UFS ISP adapter to the corresponding pins on the phone's UFS ISP pinout. Then, connect the adapter to the EasyJTAG Plus box.

Connect to PC: Connect the EasyJTAG Plus box to your computer. Next, connect the Samsung Galaxy A56 5G to the computer via a Micro USB cable to supply power to the device.

Also read: Samsung Galaxy A15 5G (SM-A156E) ISP Pinout Solution

Configure Software: On your computer, launch the EasyJTAG software. In the application's interface, select the "UFS" tab.

Identify the Chip: Click the "Identify UFS Chip" button. The software should detect the phone's memory chip and display its information.

Erase FRP Data: Navigate to the "Preset" section and select "Persistent." Finally, click the "Erase LUN0 Data" button to remove the FRP lock from the device.