Xiaomi Redmi Note 14 ISP Pinout Solution

The Xiaomi Redmi Note 14 ISP pinout is a crucial tool for advanced mobile repairs, offering a way to access the device's internal storage without needing to remove components

By using the correct ISP pinout, technicians can bypass boot failures, flash stock ROMs, or reset FRP locks effectively. The pinout can typically be found near the UFS chip, hidden beneath a metal shield, and requires precise identification of pins like CLK, TXOP, TXON, RXOP, RXON, and GND. The key to a successful repair is connecting these points to the right tools, such as UFI Box, Easy JTAG, or Medusa Pro.

Post Index:These tools allow you to interface with the device at a deep level, enabling fixes for boot loops, firmware corruption, or even a complete data recovery. It's essential to carefully check your connections, using a multimeter to ensure there's no short circuit, and confirm each step in the process. With the right equipment and patience, you can restore functionality to the Xiaomi Redmi Note 14, even when other methods fail.

Xiaomi Redmi Note 14 ISP Pinout Solution

You can quickly access the Redmi Note 14 UFS ISP pinout by following the complete guide below, which includes images. With the ISP pinout you’ll be able to restore the stock ROM, bypass FRP, or reset user data on the device using a UFi Box. This guide also explains how to reboot into Download Mode and covers the exact ISP pinout for the Xiaomi Redmi Note 14, the tools required, wiring tips, and common troubleshooting steps—based on hands‑on experience.

⚙️ What is ISP (In-System Programming)?

In simple terms, ISP allows you to access the EMMC chip without removing it from the device. By identifying the correct pinout on the board, you can connect to it using a supported UFS or EMMC tool, such as UFi, Easy JTAG, or Medusa Pro, to establish a direct connection.

ISP Pinout is particularly helpful in the following situations:

The phone is unresponsive (black screen, no boot, no charging)

FRP is locked, preventing the use of ADB, fastboot, or OTG bypass methods

You need to dump firmware from a working device to restore a dead one

Also read: Xiaomi Redmi 15C EMMC Way ISP Pinout

You’re repairing the boot partition or restoring lost partitions

The phone shows as "unknown" on the PC (EDL mode is not working)

Xiaomi Redmi Note 14 UFS ISP Pinout Image:

Xiaomi Redmi Note 14 ISP Pinout  Now, for the technical details. The Xiaomi Redmi Note 14 shares a similar hardware layout with several other models, but the exact pinout locations may differ slightly. The ISP points are typically found near the UFS chip, beneath the metal shield. Here are the key UFS ISP pin labels you’ll need:

CLK

TXOP

TXON

RXOP

RXON

GND (Ground)

💡 Tip:

Use a microscope or a 10x magnifier to accurately identify the pinout points. Don’t rely solely on diagrams—it's important to visually confirm the layout to avoid mistakes.

When dealing with dead boot issues, especially on devices like the Xiaomi Redmi Note 14, tools like Easy JTAG Plus and UFI Box dongles are invaluable for mobile repairs. They are essential in cases where the phone has been flashed incorrectly, causing it to fail to display the startup logo and become unresponsive to power.

Required Tools for ISP Pinout:

Before starting, make sure your workstation is equipped with the proper tools:

UFI Box, Easy JTAG, or Medusa Pro

0.1mm – 0.3mm jumper wire

Fine tip soldering iron

Isopropyl Alcohol (IPA 99%)

Soldering flux

Multimeter (for continuity checks)

How to Connect ISP to the EMMC Box:

Remove the battery from the phone to avoid any voltage conflicts.

Xiaomi Redmi Note 14 ISP Pinout  Clean the PCB area with isopropyl alcohol to ensure a clean surface.

Carefully solder jumper wires to the following points: CLK, TXON, TXOP, GND, RXON, and RXOP.

Connect the jumper wires to your UFS/EMMC tool, ensuring you follow the pinout of your specific tool correctly.

Also read: Xiaomi Poco X6 Pro ISP PinOUT Connection

Double-check each wire with a multimeter to ensure there are no shorts or misconnections. Once you’re sure the wiring is correct, connect your device to the UFI or Easy JTAG tool.

In the UFI or Easy JTAG software:

Select Identify UFS eMMC.

Choose the operation you want to perform, such as User Partition, Special Task, or Reset FRP. ✅